
Surface-mounted DIN-standard terminal units for oxygen, nitrous oxide, medical air, vacuum and carbon dioxide.
We plan, supply, install, test, commission and maintain medical gas pipelines for oxygen, medical air, vacuum, nitrous oxide and carbon dioxide, for a 10-bed nursing home or a multi-speciality hospital.

A medical gas pipeline system takes gas from a central source (a cylinder manifold, an oxygen plant, a compressor or a vacuum pump) and carries it through copper pipe to outlets at every bed, theatre and ICU.

Every gas has a colour-coded outlet and a gas-specific probe, so equipment can only connect to the right supply.
One team carries the project from the first site visit to maintenance years later.
Site survey, bed count and gas demand worked out, then a pipeline and manifold layout drawn for your building.
Copper pipe, outlets, valves, alarms, manifolds and plant sourced to the agreed layout and gas standard.
Pipes laid, brazed, clamped and labelled; outlets, bed head panels, valve boxes and alarms fitted.
Pressure and leak tests, cross-connection checks and flow checks at every outlet before any patient uses it.
The system brought into service, alarms set, and your staff shown how to run and isolate it.
Maintenance, repairs, extensions and spares after handover, so the supply stays safe for years.
Colour-coded outlets put each gas at the bedside without risk of a wrong connection. We supply AMICO, BS, DIN and AGSS types, surface-mounted or concealed in ABS and stainless-steel panels.

Surface-mounted DIN-standard terminal units for oxygen, nitrous oxide, medical air, vacuum and carbon dioxide.

The four outlet standards we supply, so new outlets match the equipment and probes your hospital already uses.

A flush panel carrying oxygen, nitrous oxide, medical air, vacuum and suction outlets behind one clean face.

Stainless-steel concealed outlet panel for clean areas where surfaces are wiped down often.

Stainless-steel back box that houses multiple gas outlets flush with the wall.

Mild-steel concealed outlet box, a cost-effective choice for wards and general areas.
Area valve boxes let staff isolate one zone without shutting down the hospital, and the alarm panels watch line pressure for every gas around the clock with visual and audible warnings.

A lockable, windowed box with a ball valve and pressure gauge per gas, so each zone can be isolated for maintenance or in an emergency.

Full-bore brass ball valves with lever handles for isolating pipeline sections.

Six-channel digital alarm panel with a live pressure display and high, normal and low indicators per gas.

Monitors oxygen, medical air and vacuum pressure individually, with live readings and visual and audible alarms.

Gas monitoring display and zone isolation valves combined in one lockable enclosure.

A complete zone station: four-gas alarm panel with gauges above a valve box, piped and labelled.

Gauge-based alarm for oxygen, air and vacuum with high, normal and low lamps.
The manifold room is where the supply starts. Our control panels switch between cylinder banks so the oxygen supply never breaks, with alarms and an emergency reserve.

Switches between cylinder banks on its own, keeps pressure steady and sends SMS alerts to the plant operator and the person in charge.

Wall-mounted automatic manifold panel that changes over from the empty bank to the full one with no break in supply.

Change-over panel installed with copper pigtails on a twin-bank cylinder header.

Gauge-led control panel with a left and right bank, switched by hand when one bank runs low.

Three cylinders a side, a control panel with display and gauges, solenoid valves and a beacon alarm.

A compact two-cylinder manifold with an emergency supply connection.

PSA oxygen plant linked to left and right cylinder banks and an emergency manifold or LMO tank through one automatic controller.

Brass non-return valves for manifold headers, stopping back-flow between cylinders.

Manifold rooms we have planned and installed: headers, pigtails, regulators, control panels and copper distribution.
Clean, dry medical air and dependable central suction for wards and theatres: compressors, receivers, dryers, filtration and vacuum pumps, installed and piped to every outlet.

Duplex receiver-mounted units for medical air and central vacuum, installed with filtration and distribution pipework.

The full air train: intake, pre-filter, refrigerated dryer, after-filter, receivers, line and micro filters, oil-water separator and auto drain.
The pipeline itself: copper pipe and fittings, high-pressure colour-coded tube, NIST connectors and nylon hose, laid, brazed, labelled and pressure-tested.

Non-interchangeable screw-thread connectors that make it impossible to couple the wrong gas.

Copper pipe and fittings for the medical gas distribution network.

Colour-coded high-pressure tube coils for gas connections.

Yellow nylon hose for vacuum and suction connections.

An MGPS carries medical gases such as oxygen, medical air, nitrous oxide and carbon dioxide, along with vacuum for suction, from a central source (cylinder manifolds, an oxygen plant or compressors) through a copper pipeline to outlets at each bed, theatre and ICU. It replaces moving cylinders around the wards.
We install pipelines and outlets for oxygen, medical air, vacuum (suction), nitrous oxide, carbon dioxide and nitrogen, with anaesthetic gas scavenging (AGSS) outlets for theatres.
Yes. Our head office is in Konur, Namakkal, with branches in Chennai, Vellore, Coimbatore, Madurai and Hosur. We work across Tamil Nadu and also take projects in Puducherry, Karnataka and Hyderabad / Telangana.
Yes. We add outlets and beds to existing systems, replace faulty outlets, valves and alarms, upgrade manual manifolds to automatic, and carry out leak testing and maintenance.
Both feed the pipeline from two banks of cylinders. A semi-automatic panel needs staff to switch banks by hand when one runs low; an automatic panel changes over by itself, keeps the pressure steady and raises an alarm (and, on our fully automatic panel, an SMS alert) so the supply never breaks.
Call or WhatsApp us, or send the enquiry form with the number of beds, the gases you need and your location. We will discuss the site, visit if needed, and send a quotation.
Site survey, layout, supply, installation, testing and commissioning, and service after handover. Call +91 86950 94933 or send an enquiry.